Design and In Vitro Validation of an Orthopaedic Drill Guide for Femoral Stem Revision in Total Hip Arthroplasty.

OBJECTIVE: Cemented total hip arthroplasty (THA) demonstrates superior survival rates compared to uncemented procedures. Nevertheless, most younger patients opt for uncemented THA, as removing well-fixed bone cement in the femur during revisions is complex, particularly the distal cement plug. This removal procedure often increases the risk of femoral fracture or perforation, haemorrhage and weakening bone due to poor drill control and positioning. Aim of this study was to design a novel drill guide to improve drill positioning. METHODS AND PROCEDURES: A novel orthopaedic drill guide was developed, featuring a compliant centralizer activated by a drill guide actuator. Bone models were prepared to assess centralizing performance. Three conditions were tested: drilling without guidance, guided drilling with centralizer activation held, and guided drilling with centralizer activation released. Deviations from the bone centre were measured at the entry and exit point of the drill. RESULTS: In the centralizing performance test, the drill guide significantly reduced drill hole deviations in both entry and exit points compared to the control ([Formula: see text]). The absolute deviation on the exit side of the cement plug was 10.59mm (SD 1.56) for the 'No drill guide' condition, 3.02mm (SD 2.09) for 'Drill guide - hold' and 2.12mm (SD 1.71) for 'Drill guide - release'. The compliant drill guide centralizer significantly lowered the risk of cortical bone perforation during intramedullary canal drilling in the bone models due to better control of the cement drill position. Clinical and Translational Impact Statement: The drill guide potentially reduces perioperative risks in cemented femoral stem revision. Future research should identify optimal scenarios for its application.

Osteonecrosis of the Knee: The Unintended Consequence of Steroid Abuse.

The anti-inflammatory and immunosuppressive properties of steroids allow their use in a wide variety of rheumatological diseases, asthma, inflammatory bowel disease, cancer therapy, and severe viral infections. Though life-saving or organ-saving, long-term clinical use leads to a vast array of complications. Osteoporosis is the most common orthopedic side effect of steroid abuse, while osteonecrosis is a rare occurrence. The risk of osteonecrosis appears to be dose and duration dependent, but several patient factors also play a major role and usually affect the femoral head followed by the knee joint. The long-term effects of steroids must be explained to all patients on therapy, but this risk is missed in individuals who abuse steroids for recreational or performance-enhancing purposes. We describe a male, aged 29 years, who presented with dull aching bilateral knee pain of 2-years' duration after a long-term steroid abuse for weight and muscle mass gain. Radiological and magnetic resonance imaging studies confirmed osteonecrosis of femoral and tibial condyles and secondary degenerative arthritis of the knee joint. Prompt suspicion, early diagnosis, and intervention in osteonecrosis of knee joints, and termination of steroids may reverse the pathology and prevent progression of disease.

Improving ultrasound-based bone registration using the iterative closest point algorithm paired with a complex optimization solver.

The Iterative Close Point (ICP) algorithm is used for bone registrations based on ultrasound measurements. However, the ICP has been shown to suffer from local minima. The Complex optimization, as a more robust routine compared to the commonly used gradient-based algorithms, could be an alternative for solving the ICP problem. In this study, we investigated the effect of the initial estimate and the number of registration points on bone registrations achieved using the ICP and a Complex optimization routine and we compared it against using Quadratic Sequential Programming (SQP). Ultrasound measurements were performed with an A-mode probe on a bovine humerus and an ovine femur embedded into ballistic gel. Simultaneously, the bones and the probe were tracked in 3D space using retroreflective markers. Kinematic, ultrasound and geometrical data obtained from scans of the specimens and the probe served as input to a bone registrations routine. Registrations were performed using two ICP solvers for different initial estimates and number of registration points. On average, 68 % of the Complex optimization registrations had less than 1 mm translation error and less than 1° rotational error for perturbations of the initial estimate from the reference measurements compared to the 35 % of the SQP ones. Similar medians of registration errors were observed between the two methods for variations of the number of the employed registration points. Although the Complex optimization provided accurate bone registrations for all cases, the objective function could not always determine the registrations with the smallest registration error. Future research should explore methodologies to overcome this challenge.

Mid-term results of cemented hip arthroplasties through the direct anterior approach in the lateral decubitus position: a retrospective cohort study.

BACKGROUND: Reports show a high complication rate when starting with the Direct Anterior Approach (DAA) in a supine position for hip arthroplasty. The DAA with the patient in lateral decubitus position may avoid this problem because it supposedly provides better visibility, especially on the femoral side. However, this approach did show a rather high complication rate during the adoption of the approach at 1 year follow up in our previous report. We were interested what the overall 7 year survival estimate would be and whether improvement could be seen with growing experience. METHODS: A cohort of patients undergoing total hip arthroplasty right from the start of applying the DAA in lateral decubitus position was analysed. RESULTS: In total 175 hip prostheses (162 patients) were evaluated. The 7-year survival estimate was 95.1%, 95 CI: 91.8-98.4%. In 6 of 8 revisions there was aseptic loosening of the stem. By dividing the cohort into 3 consecutive groups in time we did not see a significantly improving revision rate. CONCLUSIONS: In our experience, the adoption of the direct anterior approach in lateral decubitus position caused a relatively low 7-year survival estimate without an apparent decrease with growing experience, however given the low number of cases further research is needed to investigate the long-term risk of adopting a new approach.

Automatic measurement of lower limb alignment in portable devices based on deep learning for knee osteoarthritis.

BACKGROUND: For knee osteoarthritis patients, analyzing alignment of lower limbs is essential for therapy, which is currently measured from standing long-leg radiographs of anteroposterior X-ray (LLR) manually. To address the time wasting, poor reproducibility and inconvenience of use caused by existing methods, we present an automated measurement model in portable devices for assessing knee alignment from LLRs. METHOD: We created a model and trained it with 837 conforming LLRs, and tested it using 204 LLRs without duplicates in a portable device. Both manual and model measurements were conducted independently, then we recorded knee alignment parameters such as Hip knee ankle angle (HKA), Joint line convergence angle (JCLA), Anatomical mechanical angle (AMA), mechanical Lateral distal femoral angle (mLDFA), mechanical Medial proximal tibial angle (mMPTA), and the time required. We evaluated the model's performance compared with manual results in various metrics. RESULT: In both the validation and test sets, the average mean radial errors were 2.778 and 2.447 (P<0.05). The test results for native knee joints showed that 92.22%, 79.38%, 87.94%, 79.82%, and 80.16% of the joints reached angle deviation<1° for HKA, JCLA, AMA, mLDFA, and mMPTA. Additionally, for joints with prostheses, 90.14%, 93.66%, 86.62%, 83.80%, and 85.92% of the joints reached that. The Chi-square test did not reveal any significant differences between the manual and model measurements in subgroups (P>0.05). Furthermore, the Bland-Altman 95% limits of agreement were less than ± 2° for HKA, JCLA, AMA, and mLDFA, and slightly more than ± 2 degrees for mMPTA. CONCLUSION: The automatic measurement tool can assess the alignment of lower limbs in portable devices for knee osteoarthritis patients. The results are reliable, reproducible, and time-saving.

Trabecular bone volume fraction in Holocene and Late Pleistocene humans.

Research suggests that recent modern humans have gracile skeletons in having low trabecular bone volume fraction (BV/TV) and that gracilization of the skeleton occurred in the last 10,000 years. This has been attributed to a reduction in physical activity in the Holocene. However, there has been no thorough sampling of BV/TV in Pleistocene humans due to limited access to high resolution images of fossil specimens. Therefore, our study investigates the gracilization of BV/TV in Late Pleistocene humans and recent (Holocene) modern humans to improve our understanding of the emergence of gracility. We used microcomputed tomography to measure BV/TV in the femora, humeri and metacarpals of a sample of Late Pleistocene humans from Dolní Vestonice (Czech Republic, ∼26 ka, n = 6) and Ohalo II (Israel, ∼19 ka, n = 1), and a sample of recent humans including farming groups (n = 39) and hunter-gatherers (n = 6). We predicted that 1) Late Pleistocene humans would exhibit greater femoral and humeral head BV/TV compared with recent humans and 2) among recent humans, metacarpal head BV/TV would be greater in hunter-gatherers compared with farmers. Late Pleistocene humans had higher BV/TV compared with recent humans in both the femur and humerus, supporting our first prediction, and consistent with previous findings that Late Pleistocene humans are robust as compared to recent humans. However, among recent humans, there was no significant difference in BV/TV in the metacarpals between the two subsistence groups. The results highlight the similarity in BV/TV in the hand of two human groups from different geographic locales and subsistence patterns and raise questions about assumptions of activity levels in archaeological populations and their relationships to trabecular BV/TV.

Comparison of double chevron-cut and biplanar distal femoral osteotomy techniques: A biomechanical study.

OBJECTIVE: This study aimed to compare the stability and mechanical properties of the double chevron-cut (DCC) and biplanar (BP) distal femoral osteotomy (DFO) techniques, along with analyzing their respective contact surface areas. METHODS: Biomechanical testing was performed using sawbone and 3D modeling techniques to assess axial and torsional stability, torsional stiffness, and maximum torque of both osteotomy configurations. Additionally, 3D models of the sawbone femur were created to calculate and compare the contact surface area of the DCC, BP, and conventional single-plane DFO techniques. RESULTS: Axial stiffness and maximum strength did not significantly differ between the two osteotomy techniques. However, in terms of torsional properties, the DCC technique exhibited superior torsional stiffness compared to the BP group (27 ± 7.7 Nm/° vs. 4.5 ± 1.5 Nm/°, p = 0.008). Although the difference in maximum torque did not reach statistical significance (63 ± 10.6 vs. 56 ± 12.1, p = 0.87), it is noteworthy that the DCC group sawbone model exhibited fracture in the shaft region instead of at the osteotomy site. Therefore, the actual maximum torque of the DCC construct may not be accurately reflected by the numerical values obtained in this study. The contact surface area analysis revealed that the BP configuration had the largest contact surface area, 111% larger than that of the single-plane configuration. but 60% of it relied on the less reliable axial cut. Conversely, the DCC osteotomy offered a 31% larger contact surface area than the single-plane configuration, with both surfaces being weight-bearing. CONCLUSION: The DCC osteotomy exhibited superior mechanical stability, showing improved rotational stiffness and maximum torque when compared to the BP osteotomy. Although the BP osteotomy resulted in a larger contact surface area than the DCC osteotomy, both were larger than the conventional single-plane configuration. In clinical practice, both the DCC and BP techniques should be evaluated based on patient-specific characteristics and surgical goals.

[Research progress of femoral bone tunnel positioning in anterior cruciate ligament reconstruction].

Objective: To review the concept and methods of femoral bone tunnel positioning in anterior cruciate ligament (ACL) reconstruction, in order to provide a reference for clinical treatment. Methods: The relevant literature on the concept and methods of femoral bone tunnel positioning in ACL reconstruction in domestic and international research was extensively reviewed. Results: The position of the femoral bone tunnel is a key factor in determining the prognosis of ACL reconstruction. The concept of femoral bone tunnel positioning in ACL reconstruction has experienced isometric reconstruction, anatomical reconstruction, Ribbon-like theory, I.D.E.A.L. theory, and nearly isometric reconstruction theory. The femoral bone tunnel positioning technique is also changing with the in-depth study of the anatomy and biomechanics of the ACL, and each bone tunnel positioning technique has its own advantages and disadvantages. Over-The-Top technique is now mainly used for ACL revision; the clock-face positioning method is basically no longer applicable due to the large error, poor stability, and low retrievability; the bone landmarks positioning method (the lateral condyle of the femur's Resident's ridge and bifurcation ridge, and the the apex of the deep cartilage), which is now mostly used clinically due to the more constant anatomical landmarks. The quadrant method under X-ray fluoroscopy is more cumbersome to implement intraoperatively, so it is mainly used for academic research; computer navigation-assisted positioning has gradually become popular in recent years, which is highly accurate, avoids the influence of human factors on the positioning of the bone tunnel, and has a very good prospect of application; three-dimensional printing-assisted positioning technology, which is accurate in positioning, with a high degree of reproducibility and a short learning curve. Conclusion: The concept of femoral bone tunnel positioning for ACL reconstruction has undergone several evolutions, reflecting the deepening of the understanding of ACL and the improvement of the clinical results of reconstruction. The precision, personalization, and intelligence of positioning techniques are the focus of current and future development.

Robot-assisted anterior cruciate ligament reconstruction based on three-dimensional images.

Background Tunnel placement is a key step in anterior cruciate ligament (ACL) reconstruction. The purpose of this study was to evaluate the accuracy of bone tunnel drilling in arthroscopic ACL reconstruction assisted by a three-dimensional (3D) image-based robot system. Methods Robot-assisted ACL reconstruction was performed on twelve freshly frozen knee specimens. During the operation, three-dimensional images were used for ACL bone tunnel planning, and the robotic arm was used for navigation and drilling. Twelve patients who underwent traditional arthroscopic ACL reconstruction were included. 3D computed tomography was used to measure the actual position of the ACL bone tunnel and to evaluate the accuracy of the robotic and traditional ACL bone tunnel. Results On the femoral side, the positions of robotic and traditional surgery tunnels were 29.3 ± 1.4% and 32.1 ± 3.9% in the deep-to-shallow direction of the lateral femoral condyle (p = 0.032), and 34.6 ± 1.2% and 21.2 ± 9.4% in the high-to-low direction (p < 0.001), respectively. On the tibial side, the positions of the robotic and traditional surgical tunnels were located at 48.4 ± 0.9% and 45.8 ± 2.8% of the medial-to-lateral diameter of the tibial plateau (p = 0.008), 38.1 ± 0.8% and 34.6 ± 6.0% of the anterior-to-posterior diameter (p = 0.071), respectively. Conclusions In this study, ACL reconstruction was completed with the assistance of a robot arm and 3D images, and the robot was able to drill the bone tunnel more accurately than the traditional arthroscopic ACL reconstruction.

Treatment of Length-Unstable Pediatric Femur Fractures in Children Aged 5 to 11 years: A Focused Review.

Pediatric femur fractures in children aged 5 to 11 years are typically classified as length-stable versus length-unstable. For length-stable fracture patterns, there is frequent consensus among pediatric orthopaedic specialists regarding the appropriateness of flexible intramedullary nails, submuscular plates (SMP), or lateral-entry rigid intramedullary nails (LE-RIMN). With length-unstable fracture patterns, however, the decision is more complex. Age, weight, fracture pattern, fracture location, surgical technique, surgeon experience, several implant-specific details, and additional factors are all important when choosing between flexible intramedullary nail, SMP, and LE-RIMN. These familiar methods of fixation may all be supported by conflicting and sometimes heterogeneous data. When planning to treat length-unstable fractures in young children, surgeons should understand evidence-based details associated with each implant and how each patient-specific scenario affects perioperative decisions.

Region partitioning of articular cartilage with streaming-potential-based parameters and indentation maps.

Articular cartilage exhibits site-specific tissue inhomogeneity, for which the tissue properties may continuously vary across the articular surface. To facilitate practical applications such as studying site-specific cartilage degeneration, the inhomogeneity may be approximated with several distinct region-wise variations, with one set of tissue properties for one region. A clustering method was previously developed to partition such regions using cartilage indentation-relaxation and thickness mapping instead of simply using surface geometry. In the present study, a quantitative parameter based on streaming potential measurement was introduced as an additional feature to assess the applicability of the methodology with independent datasets. Experimental data were collected from 24 sets of femoral condyles, extracted from fresh porcine stifle joints, through streaming potential mapping, automated indentation, and needle penetration tests. K-means clustering and Elbow method were used to find optimal region partitions. Consistent with previous findings, three regions were suggested for either lateral or medial condyle regardless of left or right joint. The region shapes were approximately triangular or trapezoidal, which was similar to what was found previously. Streaming potentials were confirmed to be region-dependent, but not significantly different among joints. The cartilage was significantly thicker in the medial than lateral condyles. The region areas were consistent among joints, and comparable to that found in a previous study. The present study demonstrated the capability of region partitioning methods with different variables, which may facilitate new applications whenever site-specific tissue properties must be considered.

Small design modifications can improve the primary stability of a fully coated tapered wedge hip stem.

Increasing the stem size during surgery is associated with a higher incidence of intraoperative periprosthetic fractures in cementless total hip arthroplasty with fully coated tapered wedge stems, especially in femurs of Dorr type A. If in contrast a stem is implanted and sufficient primary stability is not achieved, such preventing successful osseointegration due to increased micromotions, it may also fail, especially if the stem is undersized. Stem loosening or periprosthetic fractures due to stem subsidence can be the consequence. The adaptation of an established stem design to femurs of Dorr type A by design modifications, which increase the stem width proximally combined with a smaller stem tip and an overall shorter stem, might reduce the risk of distal locking of a proximally inadequately fixed stem and provide increased stability. The aim of this study was to investigate whether such a modified stem design provides improved primary stability without increasing the periprosthetic fracture risk compared to the established stem design. The established (Corail, DePuy Synthes, Warsaw, IN, US) and modified stem designs (Emphasys, DePuy Synthes, Warsaw, IN, US) were implanted in cadaveric femur pairs (n = 6 pairs) using the respective instruments. Broaching and implantation forces were recorded and the contact areas between the prepared cavity and the stem determined. Implanted stems were subjected to two different cyclic loading conditions according to ISO 7206-4 using a material testing machine (1 Hz, 600 cycles @ 80 to 800 N, 600 cycles @ 80 to 1600 N). Translational and rotational relative motions between stem and femur were recorded using digital image correlation. Broaching and implantation forces for the modified stem were up to 40% higher (p = 0.024), achieving a 23% larger contact area between stem and bone (R2 = 0.694, p = 0.039) resulting in a four times lower subsidence during loading (p = 0.028). The slight design modifications showed the desired effect in this in-vitro study resulting in a higher primary stability suggesting a reduced risk of loosening. The higher forces required during the preparation of the cavity with the new broaches and during implantation of the stem could bare an increased risk for intraoperative periprosthetic fractures, which did not occur in this study.

Evaluation of the Interrater Reliability of Sonographic Measurements of Muscle Thickness of 38 Piriformis Muscles in 19 Patients with Piriformis Syndrome.

BACKGROUND The piriformis muscle is a flat superficial muscle of the deep gluteal muscles that externally rotates the hip. Ultrasound is widely used to identify the piriformis muscle, especially for guidance of the needle during injections; however, its diagnostic use has recently gained popularity. The operator-dependent nature of ultrasound requires demonstration of reliability between operators. This study aimed to evaluate interrater reliability of sonographic measurements of muscle thickness of 38 piriformis muscles in 19 patients with piriformis syndrome. MATERIAL AND METHODS An ultrasound transducer was placed transversely on the sacral spinous process and moved caudo-laterally until the piriformis muscle was visualized under the gluteus maximus while patients were lying in prone position. The thickness of piriformis muscle was measured with a 2 to 5-MHz broadband curvilinear transducer in 3 regions (thickest regions of muscle over the ilium, near the greater trochanter, and near the sacrum). The interrater reliability of measurements of 2 examiners who were blinded to each other's measurements was assessed by intraclass correlation coefficient. RESULTS In total, 114 samples from 38 piriformis muscles of 19 patients with a diagnosis of piriformis syndrome were evaluated by 2 raters in this study. The median (interquartile range) patient age was 41 (15) years. Intraclass correlation coefficient value for overall thickness measurements of piriformis muscle was 0.836. Intraclass correlation coefficient values for 3 different regions were over the ilium, near the greater trochanter, and near the sacrum were 0.777, 0.883, and 0.811, respectively. CONCLUSIONS Ultrasound measurement of piriformis muscle thickness has good interrater reliability.

Assessment of Automated Identification of Phases in Videos of Total Hip Arthroplasty Using Deep Learning Techniques.

Background: As the population ages, the rates of hip diseases and fragility fractures are increasing, making total hip arthroplasty (THA) one of the best methods for treating elderly patients. With the increasing number of THA surgeries and diverse surgical methods, there is a need for standard evaluation protocols. This study aimed to use deep learning algorithms to classify THA videos and evaluate the accuracy of the labelling of these videos. Methods: In our study, we manually annotated 7 phases in THA, including skin incision, broaching, exposure of acetabulum, acetabular reaming, acetabular cup positioning, femoral stem insertion, and skin closure. Within each phase, a second trained annotator marked the beginning and end of instrument usages, such as the skin blade, forceps, Bovie, suction device, suture material, retractor, rasp, femoral stem, acetabular reamer, head trial, and real head. Results: In our study, we utilized YOLOv3 to collect 540 operating images of THA procedures and create a scene annotation model. The results of our study showed relatively high accuracy in the clear classification of surgical techniques such as skin incision and closure, broaching, acetabular reaming, and femoral stem insertion, with a mean average precision (mAP) of 0.75 or higher. Most of the equipment showed good accuracy of mAP 0.7 or higher, except for the suction device, suture material, and retractor. Conclusions: Scene annotation for the instrument and phases in THA using deep learning techniques may provide potentially useful tools for subsequent documentation, assessment of skills, and feedback.

Midterm Comparative Analysis of Short Femoral Stem Survivorship in Dorr Type A Femurs.

Background: Proximal-distal mismatch has emerged as a prominent concern in Dorr type A femoral morphology, prompting the exploration of short stems as promising alternatives to conventional stems. This study aimed to evaluate clinical and radiographic outcomes of total hip arthroplasty (THA) using short femoral stems in Dorr type A proximal femoral morphology with a minimum follow-up of 5 years. Methods: Patients with short femoral stems in Dorr type A between 2011 and 2017 were included. Patients with the Short Modular Femoral (SMF) stem and Metha stem were recruited and patients with a shortened tapered stem (Tri-Lock BPS) were matched by propensity score matching based on age, sex, body mass index, calcar to canal ratio, and diagnosis. Patient-reported outcomes and the presence of thigh pain were assessed at 5 years postoperatively. Revision rate, complication rate, and radiographic outcomes were also assessed and compared. Results: Twenty-two cases (81%) in the SMF stem and 43 cases (65%) in the Metha stem had more than 5 years of follow-up data available. The SMF stem showed a higher failure rate than the other 2 groups, with 18% requiring revision surgery in the SMF stem compared to 4.6% in the Metha stem, and 2.3% in the Tri-Lock BPS. The SMF stem showed considerable complications such as stem position change and lateral cortical hypertrophy with inferior clinical outcomes than the other 2 stem groups. When the Metha stem and the Tri-Lock BPS groups were compared, more intraoperative fractures were observed in the Metha stem, whereas stress shielding and anterior thigh pain were significantly more prevalent in the Tri-Lock BPS. Conclusions: The SMF stem might be less reliable than previously reported, showing a high failure rate and increased radiologic complications. Thus, its use for THA in Dorr Type A femurs needs caution. On the other hand, the Metha stem showed comparable outcomes to the shortened tapered Tri-Lock BPS.

Bulky malignant peripheral nerve sheath tumour of the left thigh in a pregnant woman presenting with a pathological fracture of the proximal femur.

Malignant peripheral nerve sheath tumour (MPNST) is an aggressive soft tissue sarcoma with a poor prognosis, affecting most commonly the extremities. The lungs constitute the most frequent location for distant metastases. Half of all MPNSTs arise in patients with neurofibromatosis type 1, while approximately 10% are radiation induced and the rest are sporadic.The authors present a pregnant woman in her 40s with a sporadic MPNST of the lower limb and with lung metastases at diagnosis. Treatment consisted of interilioabdominal amputation, followed by adjuvant chemotherapy. Partial response and disease stabilisation were achieved with chemotherapy.Surgical resection with negative margins is the only potentially curative therapy, while radiation therapy and chemotherapy might be useful in the neoadjuvant or adjuvant setting, but their advantage in survival is not demonstrated. In the reported case, chemotherapy permitted the achievement of partial response and stabilisation of the disease.

A probabilistic approach for assessing the mechanical performance of intertrochanteric fracture stabilized with proximal femoral nail antirotation.

Maintaining post-operative mechanical stability is crucial for successfully healing intertrochanteric fractures treated with the Proximal Femoral Nail Antirotation (PFNA) system. This stability is primarily dependent on the bone mineral density (BMD) and strain on the fracture. Current PFNA failure analyses often overlook the uncertainties related to BMD and body weight (BW). Therefore, this study aimed to develop a probabilistic model using finite element modeling and engineering reliability analysis to assess the post-operative performance of PFNA under various physiological loading conditions. The model predictions were validated through a series of experimental test. The results revealed a negative nonlinear relationship between the BMD and compressive strain. Conversely, the BW was positively and linearly correlated with the compressive strain. Importantly, the compressive strain was more sensitive to BW than to BMD when the BMD exceeded 0.6 g/cm3. Potential trabecular bone compression failure is also indicated if BMD is equal to or below 0.15 g/cm3 and BW increases to approximately 2.5 times the normal or higher. This study emphasizes that variations in the BMD significantly affect the probability of failure of a PFNA system. Thus, careful planning of post-operative physical therapy is essential. For patients aged > 50 years restrictions on high-intensity activities are advised, while limiting strenuous movements is recommended for those aged > 65 years.

Arthroscopic Femoral Head Allograft With Proximal Femoral/Periacetabular Osteotomies for Sequelae of Perthes: A Case Report.

CASE: We describe the unique case of a 20-year-old man with a history of Legg-Calve-Perthes disease, hip dysplasia, and osteochondral fragmentation of the medial femoral head. We performed arthroscopic femoroplasty and femoral head allografting, followed by a valgus-producing derotational femoral osteotomy (DFO) and periacetabular osteotomy (PAO). At 1-year follow-up, the patient achieved osseous union and complete femoral head healing with return to his active hobbies. CONCLUSION: We describe the successful utilization of arthroscopic allografting for medial femoral head osteochondral fragmentation. To our knowledge, this is the first report on femoral head arthroscopic allografting before DFO and PAO.

Bilateral Femoral Neck Pseudarthrosis in an Adolescent Girl With Congenital Spondyloepiphyseal Dysplasia. The Treatment Journey: A Case Report.

CASE: We describe the surgical management of a girl with dwarfism and congenital spondyloepiphyseal dysplasia, who presented in adolescence with coxa vara and bilateral pseudarthrosis between the femoral neck and the diaphysis, with asymmetric distal migration at both sites and leg length discrepancy. The patient at 16 years underwent valgus osteotomy in situ and femoral neck fixation in the left hip. The right hip was operated 19 months later. CONCLUSION: Hip dysplasia is common in spondyloepiphyseal dysplasia, but a debilitating nontraumatic bilateral pseudarthrosis at the base of the femoral neck has not been previously reported. Valgus corrective osteotomies of the femur in situ led to union and allowed the patient to walk.

Magnetic resonance imaging combined with histological evaluation of repair process using the microfracture technique in an association of osteocartilaginous and meniscal surgically induced lesions of the knee. In vivo experiment on a rabbit model.

The present research study aimed to assess magnetic resonance imaging (MRI) changes and histological findings in the therapeutic effects of microfractures in the treatment of complex animal knee lesions resulting from osteochondral and meniscal defects resulting from non-total meniscectomies. The anterior cruciate ligament lesions are also proven to facilitate the development of osteoarthritis in the knee and worsen the prognosis. Surgery was performed on the right knee joint of 22 male rabbits in order to partially remove the anterior horn of the internal meniscus and to induce an osteochondral defect at the level of the internal femoral condyle. The induced lesion complex was aimed to simulate a clinical situation that occurs frequently in orthopedic practice when young adults undergo partial meniscectomy and at the time of surgery, an osteochondral defect is diagnosed. Rabbits were separated into two study groups: the control (C1) group and the microfractures (MF2) group. After the induced cartilage defect and partial meniscectomy, both groups were followed-up for six months using detailed MRI. Also, anatomical specimens were histologically analyzed to show modifications and signs of healing process, along with complications, in the study group. The results showed that the microfracture group had better results concerning articular surface defect healing in comparison to the control group. Our results suggest that microfractures do improve results concerning surface contact healing and serial MRI studies can be useful in observing the remodeling process in dynamics.